Admin Features

From Holdfast: Nations At War
Jump to navigation Jump to search

Unless stated otherwise, all server config commands listed in this page are global rotation commands, which means that they can either be placed inside a map rotation to apply to that rotation only, or else before the map rotations section to apply to all map rotations.

Ray-Gun System

When logged in as admin, any player you are aiming at should have their name highlighted in green. If you open the Round Players Panel while a player is highlighted (default "P" keybind) that player will be automatically selected for quick admin action access. Common actions also have their own hotkey shortcuts for even quicker access:

Number Key Action
1 Private Message
2 Slay
3 Revive
4 Slap
5 Heal
6 Bring
7 Go To
8 Temp Voip Mute
9 Temp Chat Mute

When the dialog box is open after pressing an admin action key, you can press the "Enter" key for quick confirmation.

You can toggle the admin ray-gun system between "Always On", "Freeflight Only", and "Off" modes via a button at the bottom of the Round Players Panel.

Fire Out of Line

Fire Out of Line (FOL) only allows shooting firearms while players are within a line. To enable it, use:

fol_enabled true

There are 4 different settings that you can set either globally or per player class.

Setting Name Description Default Value
radius The farthest distance (in metres) a player can be from a player line in order to be considered part of the line. 1.5 (m)
mounted_radius Same as "radius" but only relevant while the player is mounted on a horse. 25 (m)
artillery_radius If a player is within this distance to an artillery piece, they can fire even if not within a line. 0 (disabled)
players_needed The minimum number of players needed - including the local player - to form a valid line. 3

Some classes have specific default value overrides, listed here:

Class Setting Override Value
Light Infantry radius 5
Rifleman radius 5
Cannoneer artillery_radius 15
Rocketeer artillery_radius 15
Sapper artillery_radius 15

To override the defaults for all classes with your own values, use:

fol_default <FOLSettingName> <value>

You can also override any default value for any specific class. To do this, use:

fol_class <PlayerClass> <FOLSettingName> <value>

When a player dies, a temporary "ghost" will spawn in their place so that the line doesn't immediately break. The default ghost lifetime is 3 seconds. You can change this via this command:

fol_ghost_duration <value>

If a player fires out of line, they will be blocked from firing again for a default duration of 2 seconds. You can change this value via this command:

fol_fire_block_duration <value>

You can also punish players that fire out of line with automatically applied slap damage. You can do this via this command, which is set to 0 by default:

fol_slap_damage <value>


Example:

fol_enabled true
fol_slap_damage 50
fol_fire_block_duration 5
fol_ghost_duration 4
fol_default players_needed 5
fol_default radius 2
fol_class rifleman radius 10
fol_class light_infantry players_needed 2
fol_class light_infantry artillery_radius 10

For a rotation containing FOL commands as in the example above:

  • If a player fires out of line, he will take 50 slap damage and he will also be blocked from firing again for 5 seconds.
  • If a player dies, his ghost will still form part of a valid line for 4 seconds after death.
  • By default, for a line to be valid it will need to contain a minimum of 5 players.
  • By default, a player will need to be at most 2m away from another player that is part of a line to also form part that line.
  • Riflemen can be 10m away from a line of players to be able to shoot, instead of just 2m. However, if they are more than 2m away from their line, they will not be counted as part of a line for other non-riflemen.
  • Light infantry will be able to shoot if they are part of a line that contains just 2 players, i.e. they just have to be next to 1 other player. However, if the line contains less than 5 players, any other non-light infantry players in the line will not be able to shoot.
  • If a light infantry is within 10m distance from an artillery piece, they will be able to shoot even if they are not part of any line.

All Charge

When All Charge is activated, firing is restricted. It can be enabled at any time via the RC command:

rc ac <delay>

(inputting no delay parameter defaults to a value of 0)

A delay value of 0 triggers an All Charge immediately.

A delay value of -1 cancels any active or pending All Charge.


You can also have All Charge trigger automatically by setting the auto trigger mode. There are 4 different modes.

Mode Name Description
none Auto trigger system disabled.
time_only All Charge will trigger at a set round time.
percent_only All Charge will trigger after the percentage players left alive is equal or lower than the set value (only applies to game modes with a round spawn close time).
percent_or_time All Charge will trigger when either the time condition or the percent condition is met, whichever becomes true first.

To set the Auto Trigger Mode, use:

all_charge_auto_trigger_mode <AutoTriggerMode>
Other All Charge Commands
Config Command Description Argument
all_charge_trigger_delay If set, players will be notified about any scheduled all charge this amount of seconds before the time trigger. float (s)
all_charge_time_trigger Sets the round time value for the auto trigger system. float (s)
all_charge_percent_players_trigger Sets the percent value for the auto trigger system. float (0-1 range)
all_charge_percent_trigger_min_players_needed The percent trigger will only activate if the round started with a minimum of this number of players. int
all_charge_block_pistol_fire Sets whether to block pistol fire during All Charge. bool
all_charge_block_artillery_fire Sets whether to block artillery fire during All Charge. bool
all_charge_slow_cavalry Sets whether cavalry should be restricted to a slow speed during All Charge. bool


Example:

all_charge_auto_trigger_mode time_only
all_charge_time_trigger 300
all_charge_trigger_delay 30
all_charge_block_pistol_fire false

For a rotation containing all charge commands as in the example above, at time 5:30, all players will be notified that All Charge will activate at 5:00. Then at 5:00 All Charge will become active, but pistols will still be usable.

Artillery Settings

The first player to use an artillery piece in a round gets listed as the claimant of that piece in the Artillery Priority Panel. If the same player claims another artillery piece, then the first claim will get revoked. Notifications will be sent to both the claimant player and any player who tries to use an artillery piece that is already claimed, if enabled via this config command:

arty_claiming_notifications true
Other Artillery Commands
Config Command Description
arty_firing_start_time Disables artillery firing until the set time in seconds has passed.
arty_on_arty_start_time Disables artillery fire damaging other artillery pieces until the set time in seconds has passed.

Map Rotations Panel

The map rotations panel shows a list of all rotations in the server config. You can rotate to any map and can even choose to load a rotation with different factions than those set in the config file.

Mod map names will be listed as "Custom Mod Map" by default. However, you can set a custom name for rotations that use mod maps in the server config file by using this command:

map_name_override <name>